LTE TDD
For Waveform Playback (ARB) capability.
This topic describes the settings of the Downlink > DL-SCH node for an Advanced TDD Downlink carrier.
Modulation and TBS Index Table
Transmission Configuration Length
Transmit Antenna Weight for Port 5
Transmit Antenna Weight for Port 7
Transmit Antenna Weight for Port 8
Transmit Antenna Weight for Port 9
Transmit Antenna Weight for Port 10
Transmit Antenna Weight for Port 11
Transmit Antenna Weight for Port 12
Transmit Antenna Weight for Port 13
Transmit Antenna Weight for Port 14
DL-SCH is a fixed collection of 8 channels. Setting described below apply to each DL-SCH<N> instance.
Configures the per-subframe PDSCH transmission (Tx Config) sequence for this DL-SCH channel. Up to 40 sequences.
Click the button in the Transmission Configuration cell to open the DL-SCH Tx sequence window.
Enables or disables this PDSCH Tx sequence.
|
SCPI Command |
[:SOURce]:RADio:LTETdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<N>:TX<seq>:[:STATe] ON|OFF|1|0 [:SOURce]:RADio:LTETdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<N>:TX<seq>:[:STATe]? |
|
SCPI Example |
:RADio:LTETdd:WAVeform:ARB:CCARrier:DLINk:DLSCh:TX:STATe ON :RADio:LTETdd:WAVeform:ARB:CCARrier:DLINk:DLSCh:TX:STATe? |
|
Notes |
Per-subframe setting (seq 1-n, where n is the value of Tx Param Length). |
|
Dependencies |
This setting is not visible when state is OFF. |
|
Preset |
1 |
|
State Saved |
Yes |
|
Min |
N/A |
|
Max |
N/A |
|
Initial S/W Revision |
A.20.01 |
Turns the re-transmission state of transport block/codeword 0 on or off for this PDSCH Tx sequence.
|
SCPI Command |
[:SOURce]:RADio:LTETdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<N>:TX<seq>:RETX0 ON|OFF|1|0 [:SOURce]:RADio:LTETdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<N>:TX<seq>:RETX0? |
|
SCPI Example |
:RADio:LTETdd:WAVeform:ARB:CCARrier:DLINk:DLSCh:TX:RETX0 OFF :RADio:LTETdd:WAVeform:ARB:CCARrier:DLINk:DLSCh:TX:RETX0? |
|
Notes |
Per-subframe setting (seq 1-n, where n is the value of Tx Param Length). |
|
Dependencies |
This setting is not visible when state is OFF |
|
Preset |
0 |
|
State Saved |
Yes |
|
Min |
N/A |
|
Max |
N/A |
|
Initial S/W Revision |
A.20.01 |
Turns the re-transmission state of transport block/codeword 1 on or off for this PDSCH Tx sequence.
|
SCPI Command |
[:SOURce]:RADio:LTETdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<N>:TX<seq>:RETX1 ON|OFF|1|0 [:SOURce]:RADio:LTETdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<N>:TX<seq>:RETX1? |
|
SCPI Example |
:RADio:LTETdd:WAVeform:ARB:CCARrier:DLINk:DLSCh:TX:RETX1 OFF :RADio:LTETdd:WAVeform:ARB:CCARrier:DLINk:DLSCh:TX:RETX1? |
|
Notes |
Per-subframe setting (seq 1-n, where n is the value of Tx Param Length). |
|
Dependencies |
This setting is not visible when state is OFF and Number od Codewords is 1. |
|
Preset |
0 |
|
State Saved |
Yes |
|
Min |
N/A |
|
Max |
N/A |
|
Initial S/W Revision |
A.20.01 |
Enter a value for the MCS Index for codeword 0.
|
SCPI Command |
[:SOURce]:RADio:LTETdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<N>:TX<seq>:MCS0 <integer> [:SOURce]:RADio:LTETdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<N>:TX<seq>:MCS0? |
|
SCPI Example |
:RADio:LTETdd:WAVeform:ARB:CCARrier:DLINk:DLSCh:TX:MCS0 0 :RADio:LTETdd:WAVeform:ARB:CCARrier:DLINk:DLSCh:TX:MCS0? |
|
Range |
0 to 31 |
|
Dependencies |
This setting is not visible when state is OFF |
|
Couplings |
Controls TBS Index (0), Modulation (0) when Transmission Setting Mode is MCS. |
|
Preset |
0 |
|
State Saved |
Yes |
|
Min |
0 |
|
Max |
31 |
|
Initial S/W Revision |
A.20.01 |
Enter a value for the MCS Index for codeword 1.
|
SCPI Command |
[:SOURce]:RADio:LTETdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<N>:TX<seq>:MCS1 <integer> [:SOURce]:RADio:LTETdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<N>:TX<seq>:MCS1? |
|
SCPI Example |
:RADio:LTETdd:WAVeform:ARB:CCARrier:DLINk:DLSCh:TX:MCS1 0 :RADio:LTETdd:WAVeform:ARB:CCARrier:DLINk:DLSCh:TX:MCS1? |
|
Range |
0 to 31 |
|
Dependencies |
This setting is not visible when state is OFF and Number od Codewords is 1. |
|
Couplings |
Controls TBS Index (1), Modulation (1) when Transmission Setting Mode is MCS. |
|
Preset |
0 |
|
State Saved |
Yes |
|
Min |
0 |
|
Max |
31 |
|
Initial S/W Revision |
A.20 |
Query only
Displays the TBS Index for codeword 0.
|
SCPI Command |
[:SOURce]:RADio:LTETdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<N>:TX<seq>:TBSi0? |
|
SCPI Example |
:RADio:LTETdd:WAVeform:ARB:CCARrier:DLINk:DLSCh:TX:TBSi0? |
|
Notes |
Read-only, derived from MCS Index 0. |
|
Dependencies |
Set by software from MCS Index 0. This setting is not visible when state is OFF |
|
Preset |
0 |
|
State Saved |
No |
|
Min |
0 |
|
Max |
26 |
|
Initial S/W Revision |
A.20.01 |
Query only
Displays the TBS Index for codeword 1.
|
SCPI Command |
[:SOURce]:RADio:LTETdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<N>:TX<seq>:TBSi1? |
|
SCPI Example |
:RADio:LTETdd:WAVeform:ARB:CCARrier:DLINk:DLSCh:TX:TBSi1? |
|
Notes |
Read-only, derived from MCS Index 1. |
|
Dependencies |
Set by software from MCS Index 1. This setting is not visible when state is OFF and Number od Codewords is 1. |
|
Preset |
0 |
|
State Saved |
No |
|
Min |
0 |
|
Max |
26 |
|
Initial S/W Revision |
A.20 |
Query only
Displays the Transport Block Size for codeword 0.
|
SCPI Command |
[:SOURce]:RADio:LTETdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<N>:TX<seq>:TBSZ0? |
|
SCPI Example |
:RADio:LTETdd:WAVeform:ARB:CCARrier:DLINk:DLSCh:TX:TBSZ0? |
|
Notes |
Read-only, derived from TBS Index (0). |
|
Dependencies |
Set by software from TBS Index (0). This setting is not visible when state is OFF |
|
Preset |
1 |
|
State Saved |
No |
|
Min |
1 |
|
Max |
391656 |
|
Initial S/W Revision |
A.20.01 |
Query only
Displays the Transport Block Size for codeword 1.
|
SCPI Command |
[:SOURce]:RADio:LTETdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<N>:TX<seq>:TBSZ1? |
|
SCPI Example |
:RADio:LTETdd:WAVeform:ARB:CCARrier:DLINk:DLSCh:TX:TBSZ1? |
|
Notes |
Read-only, derived from TBS Index (1). |
|
Dependencies |
Set by software from TBS Index (1). This setting is not visible when state is OFF and Number od Codewords is 1. |
|
Preset |
1 |
|
State Saved |
No |
|
Min |
1 |
|
Max |
391656 |
|
Initial S/W Revision |
A.20 |
Query only
Displays the modulation type for codeword 0.
|
SCPI Command |
[:SOURce]:RADio:LTETdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<N>:TX<seq>:MOD0? |
|
SCPI Example |
:RADio:LTETdd:WAVeform:ARB:CCARrier:DLINk:DLSCh:TX:MOD0? |
|
Choices |
QPSK | 16QAM | 64QAM | 256QAM | 1024QAM. Read-only, derived from MCS Index 0 |
|
Dependencies |
Set by software from MCS Index 0. This setting is not visible when state is OFF |
|
Preset |
QPSK |
|
State Saved |
No |
|
Min |
N/A |
|
Max |
N/A |
|
Initial S/W Revision |
A.20.01 |
Query only
Displays the modulation type for codeword 1.
|
SCPI Command |
[:SOURce]:RADio:LTETdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<N>:TX<seq>:MOD1? |
|
SCPI Example |
:RADio:LTETdd:WAVeform:ARB:CCARrier:DLINk:DLSCh:TX:MOD1? |
|
Choices |
QPSK | 16QAM | 64QAM | 256QAM | 1024QAM. Read-only, derived from MCS Index 1. |
|
Dependencies |
Set by software from MCS Index 1. |
|
Couplings |
This setting is not visible when state is OFF and Number od Codewords is 1. |
|
Preset |
QPSK |
|
State Saved |
No |
|
Min |
N/A |
|
Max |
N/A |
|
Initial S/W Revision |
A.20 |
Sets the Redundancy Version (RV) index for codeword 0.
|
SCPI Command |
[:SOURce]:RADio:LTETdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<N>:TX<seq>:RVID0 <integer> [:SOURce]:RADio:LTETdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<N>:TX<seq>:RVID0? |
|
SCPI Example |
:RADio:LTETdd:WAVeform:ARB:CCARrier:DLINk:DLSCh:TX:RVID0 0 :RADio:LTETdd:WAVeform:ARB:CCARrier:DLINk:DLSCh:TX:RVID0? |
|
Range |
0 to 3 |
|
Dependencies |
This setting is not visible when state is OFF. |
|
Preset |
0 |
|
State Saved |
Yes |
|
Min |
0 |
|
Max |
3 |
|
Initial S/W Revision |
A.20.01 |
Sets the Redundancy Version (RV) index for codeword 1.
|
SCPI Command |
[:SOURce]:RADio:LTETdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<N>:TX<seq>:RVID1 <integer> [:SOURce]:RADio:LTETdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<N>:TX<seq>:RVID1? |
|
SCPI Example |
:RADio:LTETdd:WAVeform:ARB:CCARrier:DLINk:DLSCh:TX:RVID1 0 :RADio:LTETdd:WAVeform:ARB:CCARrier:DLINk:DLSCh:TX:RVID1? |
|
Range |
0 to 3 |
|
Dependencies |
This setting is not visible when state is OFF and Number od Codewords is 1. |
|
Preset |
0 |
|
State Saved |
Yes |
|
Min |
0 |
|
Max |
3 |
|
Initial S/W Revision |
A.20 |
Sets the RBG Bitmap.
|
SCPI Command |
[:SOURce]:RADio:LTETdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<N>:TX<seq>:RBG:BITMap:USER <string> [:SOURce]:RADio:LTETdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<N>:TX<seq>:RBG:BITMap:USER? |
|
SCPI Example |
:RADio:LTETdd:WAVeform:CCARrier:DLINk:DLSCh:TX:RBG:BITMap:USER "11111111111111110" :RADio:LTETdd:WAVeform:CCARrier:DLINk:DLSCh:TX:RBG:BITMap:USER? |
|
Notes |
Binary string of 0s and 1s. Length depends on System Bandwidth. |
|
Dependencies |
This setting is not visible when state is OFF. |
|
Couplings |
|
|
Preset |
"1111111111111" |
|
State Saved |
Yes |
|
Min |
N/A |
|
Max |
N/A |
|
Initial S/W Revision |
A.20 |
Sets the resource block (RB) offset for this PDSCH Tx sequence.
|
SCPI Command |
[:SOURce]:RADio:LTETdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<N>:TX<seq>:RBOFfset <integer> [:SOURce]:RADio:LTETdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<N>:TX<seq>:RBOFfset? |
|
SCPI Example |
:RADio:LTETdd:WAVeform:ARB:CCARrier:DLINk:DLSCh:TX:RBOFfset 0 :RADio:LTETdd:WAVeform:ARB:CCARrier:DLINk:DLSCh:TX:RBOFfset? |
|
Dependencies |
Applies to Resource Allocation Type 2. |
|
Preset |
0 |
|
State Saved |
Yes |
|
Min |
0 |
|
Max |
99 |
|
Initial S/W Revision |
A.20.01 |
Sets the number of resource blocks in the frequency domain for this PDSCH Tx sequence.
|
SCPI Command |
[:SOURce]:RADio:LTETdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<N>:TX<seq>:RBSize <integer> [:SOURce]:RADio:LTETdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<N>:TX<seq>:RBSize? |
|
SCPI Example |
:RADio:LTETdd:WAVeform:ARB:CCARrier:DLINk:DLSCh:TX:RBSize 0 :RADio:LTETdd:WAVeform:ARB:CCARrier:DLINk:DLSCh:TX:RBSize? |
|
Dependencies |
Applies to Resource Allocation Type 2. This setting is not visible when state is OFF. |
|
Preset |
50 |
|
State Saved |
Yes |
|
Min |
1 |
|
Max |
100 |
|
Initial S/W Revision |
A.20.01 |
Sets the PDSCH resource element mapping and quasi co-location (QCL) indicator for this PDSCH Tx sequence.
|
SCPI Command |
[:SOURce]:RADio:LTETdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<N>:TX<seq>:REMQ <integer> [:SOURce]:RADio:LTETdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<N>:TX<seq>:REMQ? |
|
SCPI Example |
:RADio:LTETdd:WAVeform:ARB:CCARrier:DLINk:DLSCh:TX:REMQ 0 :RADio:LTETdd:WAVeform:ARB:CCARrier:DLINk:DLSCh:TX:REMQ? |
|
Dependencies |
Visible when the Transmission Mode selection is 10. This setting is not visible when state is OFF. |
|
Preset |
0 |
|
State Saved |
Yes |
|
Min |
0 |
|
Max |
3 |
|
Initial S/W Revision |
A.20.01 |
Query only
Displays the identifying number of the selected channel.
|
SCPI Command |
[:SOURce]:RADio:LTETdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<N>:CHANnel? |
|
SCPI Example |
:RADio:LTETdd:WAVeform:ARB:CCARrier:DLINk:DLSCh:CHANnel? |
|
Preset |
5 |
|
State Saved |
No |
|
Min |
N/A |
|
Max |
N/A |
|
Initial S/W Revision |
A.20.01 |
Selects the RNTI type.
See 3GPP TS 36.321 7.1 for more information.
|
SCPI Command |
[:SOURce]:RADio:LTETdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<N>:RTYPe C|SI|P [:SOURce]:RADio:LTETdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<N>:RTYPe? |
|
SCPI Example |
:RADio:LTETdd:WAVeform:ARB:CCARrier:DLINk:DLSCh:RTYPe C :RADio:LTETdd:WAVeform:ARB:CCARrier:DLINk:DLSCh:RTYPe? |
|
Choices |
C-RNTI (Dedicated Traffic) | SI-RNTI (System Information) | P-RNTI (Paging) |
|
Preset |
C |
|
State Saved |
Yes |
|
Min |
N/A |
|
Max |
N/A |
|
Initial S/W Revision |
A.20.01 |
Selects PDSCH relative power. This power value is applied to all allocations that belong to the UE. For more details, refer to 3GPP TS 36.213 and 36.331.
|
SCPI Command |
[:SOURce]:RADio:LTETdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<N>:PA OFF|M6DB|M4_77db|M3DB|M1_77db|ZERodb|P1DB|P2DB|P3DB [:SOURce]:RADio:LTETdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<N>:PA? |
|
SCPI Example |
:RADio:LTETdd:WAVeform:ARB:CCARrier:DLINk:DLSCh:PA ZERodb :RADio:LTETdd:WAVeform:ARB:CCARrier:DLINk:DLSCh:PA? |
|
Choices |
Off | -6 dB | -4.77 dB | -3 dB | -1.77 dB | 0 dB | 1 dB | 2 dB | 3 dB |
|
Dependencies |
The selected P_A value is applied to the Power parameter. In case P_A parameter is not off (-6 dB to 3 dB), P_A parameter is prior to the Power parameter. |
|
Couplings |
Coupled with Power |
|
Preset |
ZERodb |
|
State Saved |
Yes |
|
Min |
N/A |
|
Max |
N/A |
|
Initial S/W Revision |
A.20.01 |
Enables or disables the channel.
|
SCPI Command |
[:SOURce]:RADio:LTETdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<N>:[:STATe] ON|OFF|1|0 [:SOURce]:RADio:LTETdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<N>:[:STATe]? |
|
SCPI Example |
:RADio:LTETdd:WAVeform:ARB:CCARrier:DLINk:DLSCh:STATe OFF :RADio:LTETdd:WAVeform:ARB:CCARrier:DLINk:DLSCh:STATe? |
|
Preset |
1 |
|
State Saved |
Yes |
|
Min |
N/A |
|
Max |
N/A |
|
Initial S/W Revision |
A.20.01 |
Sets a power level, in dB for the selected channel.
|
SCPI Command |
[:SOURce]:RADio:LTETdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<N>:POWer <rel_ampl> [:SOURce]:RADio:LTETdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<N>:POWer? |
|
SCPI Example |
:RADio:LTETdd:WAVeform:ARB:CCARrier:DLINk:DLSCh:POWer 0 :RADio:LTETdd:WAVeform:ARB:CCARrier:DLINk:DLSCh:POWer? |
|
Notes |
Power relative to the average subcarrier power (dB). |
|
Preset |
0 |
|
State Saved |
Yes |
|
Min |
-60 |
|
Max |
20 |
|
Initial S/W Revision |
A.20.01 |
Sets a value, in decimal for the Radio Network Temporary Identifier (RNTI).
|
SCPI Command |
[:SOURce]:RADio:LTETdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<N>:RNTi <integer> [:SOURce]:RADio:LTETdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<N>:RNTi? |
|
SCPI Example |
:RADio:LTETdd:WAVeform:ARB:CCARrier:DLINk:DLSCh:RNTi 1 :RADio:LTETdd:WAVeform:ARB:CCARrier:DLINk:DLSCh:RNTi? |
|
Notes |
Range: (It depends on RNTI Type in DL-SCH.) 0 to 65533 (C-RNT, see note) 65534 (P-RNTI) 65535 (SI-RNTI), |
|
Preset |
1 |
|
State Saved |
Yes |
|
Min |
0 |
|
Max |
65535 |
|
Initial S/W Revision |
A.20.01 |
Turns scrambling for the PDSCH codeword on or off.
|
SCPI Command |
[:SOURce]:RADio:LTETdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<N>:SCRamble[:STATe] ON|OFF|1|0 [:SOURce]:RADio:LTETdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<N>:SCRamble[:STATe]? |
|
SCPI Example |
:RADio:LTETdd:WAVeform:ARB:CCARrier:DLINk:DLSCh:SCRamble:STATe ON :RADio:LTETdd:WAVeform:ARB:CCARrier:DLINk:DLSCh:SCRamble:STATe? |
|
Preset |
1 |
|
State Saved |
Yes |
|
Min |
N/A |
|
Max |
N/A |
|
Initial S/W Revision |
A.20.01 |
Sets UE Category for the corresponding DL-SCH.
The maximum number of supported layers for spatial multiplexing in DL is specified for each category.
The maximum transport block size determined by UE Category is checked during generation process.
See 3GPP TS 36.212 and 36.306 for more information.
|
SCPI Command |
[:SOURce]:RADio:LTETdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<n>:UECategory CAT0|CAT1|CAT2|CAT3|CAT4|CAT5|CAT62l|CAT64l|CAT72l|CAT74l|CAT8|CAT92l|CAT94l|CAT102l|CAT104l|CAT112l|CAT114l|CAT122l|CAT124l|CAT132l|CAT134l|CAT14|CAT152l|CAT154l|CAT162l|CAT164l|CAT17|CAT182l|CAT184l|CAT188l|CAT192l|CAT194l|CAT198l|CAT202l|CAT204l|CAT208l|CAT212l|CAT214l [:SOURce]:RADio:LTETdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<n>:UECategory? |
|
SCPI Example |
RADio:LTETdd:WAVeform:CCARrier:DLINk:DLSCh:UECategory CAT14 RADio:LTETdd:WAVeform:CCARrier:DLINk:DLSCh:UECategory? |
|
Notes |
Non-BL/CE choices: 0 to 21 with layer variants BL/CE: M1 (Fixed) |
|
Preset |
CAT14 |
|
State Saved |
Yes |
|
Min |
N/A |
|
Max |
N/A |
|
Initial S/W Revision |
A.20.01 |
Sets the Transmission Mode for the corresponding DL-SCH.
1: Single Antenna Port (Port 0)
2: Transmit Diversity
3: Open-loop Spatial Multiplexing
4: Closed-loop Spatial Multiplexing
5: Multi-user MIMO
6: Closed-loop Spatial Multiplexing with Single Layer
7: Single Antenna Port (Port 5)
8: Single Antenna Port (Port 7 or 8)/Dual Layer Transmission (Ports 7 and 8)
9: Single Antenna Port (Port 7 or 8)/Up to 8 Layer Transmission (Ports 7 to 14)
10: Single Antenna Port (Port 7 or 8)/Up to 8 Layer Transmission (Ports 7 to 14)
|
SCPI Command |
[:SOURce]:RADio:LTETdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<N>:TMODe TM1|TM2|TM3|TM4|TM5|TM6|TM7|TM8|TM9|TM10 [:SOURce]:RADio:LTETdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<N>:TMODe? |
|
SCPI Example |
:RADio:LTETdd:WAVeform:ARB:CCARrier:DLINk:DLSCh:TMODe TM1 :RADio:LTETdd:WAVeform:ARB:CCARrier:DLINk:DLSCh:TMODe? |
|
Choices |
TM8 is not available with Extended CP. When PDCCH Allocations=4 with 1.4 MHz and Normal CP: TM7 not available. When RNTI Type is P-RNTI, SI-RNTI or RA-RNTI, auto-set to TM1 (single) or TM2 (multi) and read-only. |
|
Couplings |
Controls Number of Layers, Precoding Method, Diversity Method. |
|
Preset |
TM1 |
|
State Saved |
Yes |
|
Min |
N/A |
|
Max |
N/A |
|
Initial S/W Revision |
A.20.01 |
Turns the coding state On or Off.
|
SCPI Command |
[:SOURce]:RADio:LTETdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<N>:CODing[:STATe] ON|OFF|1|0 [:SOURce]:RADio:LTETdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<N>:CODing[:STATe]? |
|
SCPI Example |
:RADio:LTETdd:WAVeform:ARB:CCARrier:DLINk:DLSCh:CODing:STATe ON :RADio:LTETdd:WAVeform:ARB:CCARrier:DLINk:DLSCh:CODing:STATe? |
|
Notes |
This setting applies to the DCI, BCH, and DL-SCH channels. |
|
Preset |
1 |
|
State Saved |
Yes |
|
Min |
N/A |
|
Max |
N/A |
|
Initial S/W Revision |
A.20.01 |
Selects the data source for codeword/transport block 0 of the DL-SCH. Use the Data Source Selection dialog box to select PN9, PN15 for the data in data stream 0 (transport block 0) of DL-SCH.
|
SCPI Command |
[:SOURce]:RADio:LTETdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<N>:DATa PN9|PN15 [:SOURce]:RADio:LTETdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<N>:DATa? |
|
SCPI Example |
:RADio:LTETdd:WAVeform:ARB:CCARrier:DLINk:DLSCh:DATa PN9 :RADio:LTETdd:WAVeform:ARB:CCARrier:DLINk:DLSCh:DATa? |
|
Preset |
PN9 |
|
State Saved |
Yes |
|
Min |
N/A |
|
Max |
N/A |
|
Initial S/W Revision |
A.20.01 |
Use the Data Source Selection dialog box to select User Defined Bits for the data in data stream 0 (transport block 0) of DL-SCH.
|
SCPI Command |
[:SOURce]:RADio:LTETdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<N>:DATa:USER <string> [:SOURce]:RADio:LTETdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<N>:DATa:USER? |
|
SCPI Example |
:RADio:LTETdd:WAVeform:ARB:CCARrier:DLINk:DLSCh:DATa:USER "00000000" :RADio:LTETdd:WAVeform:ARB:CCARrier:DLINk:DLSCh:DATa:USER? |
|
Preset |
"00000000" |
|
State Saved |
Yes |
|
Min |
N/A |
|
Max |
N/A |
Query only
Displays the data source for codeword/transport block 1 of the DL-SCH.
|
SCPI Command |
[:SOURce]:RADio:LTETdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<N>:DATa1? |
|
SCPI Example |
:RADio:LTETdd:WAVeform:ARB:CCARrier:DLINk:DLSCh:DATa1? |
|
Dependencies |
Only applicable when Number of Codewords is 2. |
|
Preset |
PN9 |
|
State Saved |
Yes |
|
Min |
N/A |
|
Max |
N/A |
|
Initial S/W Revision |
A.20.01 |
Selects the data source for codeword/transport block 1 of the DL-SCH.
Use the Data Source Selection dialog box to select User Defined Bits for the data in data stream 1 (transport block 1) of DL-SCH.
|
SCPI Command |
[:SOURce]:RADio:LTETdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<N>:DATa1:USER? |
|
SCPI Example |
:RADio:LTETdd:WAVeform:ARB:CCARrier:DLINk:DLSCh:DATa1:USER? |
|
Dependencies |
Only applicable when Number of Codewords is 2. |
|
Preset |
"00000000" |
|
State Saved |
Yes |
|
Min |
N/A |
|
Max |
N/A |
|
Initial S/W Revision |
A.20.01 |
Selects TBS Index Alt.
|
SCPI Command |
[:SOURce]:RADio:LTETdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<N>:TBSalt NONe|A26|A33 [:SOURce]:RADio:LTETdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<N>:TBSalt? |
|
SCPI Example |
:RADio:LTETdd:WAVeform:ARB:CCARrier:DLINk:DLSCh:TBSalt NONe :RADio:LTETdd:WAVeform:ARB:CCARrier:DLINk:DLSCh:TBSalt? |
|
Notes |
None and 26A are available when:
None and 33A are available for other Table 1/TM combinations. See 3GPP TS 36.213 Table 7.1.7.1-1A. |
|
Preset |
NONe |
|
State Saved |
Yes |
|
Min |
N/A |
|
Max |
N/A |
|
Initial S/W Revision |
A.20.01 |
Selects TBS Index Alt2.
|
SCPI Command |
[:SOURce]:RADio:LTETdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<N>:TBSalt2 NONe|B33 [:SOURce]:RADio:LTETdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<N>:TBSalt2? |
|
SCPI Example |
:RADio:LTETdd:WAVeform:ARB:CCARrier:DLINk:DLSCh:TBSalt2 NONe :RADio:LTETdd:WAVeform:ARB:CCARrier:DLINk:DLSCh:TBSalt2? |
|
Notes |
None and 33B are available when Modulation and TBS Index Table is Table 2/3/4 and Transmission Mode is 1, 2, 3, 4, 6 or 7. Otherwise set to None and read-only. |
|
Preset |
NONe |
|
State Saved |
Yes |
|
Min |
N/A |
|
Max |
N/A |
|
Initial S/W Revision |
A.20.01 |
Selects TBS Index Alt3.
|
SCPI Command |
[:SOURce]:RADio:LTETdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<N>:TBSalt3 NONe|A37 [:SOURce]:RADio:LTETdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<N>:TBSalt3? |
|
SCPI Example |
:RADio:LTETdd:WAVeform:ARB:CCARrier:DLINk:DLSCh:TBSalt3 NONe :RADio:LTETdd:WAVeform:ARB: CCARrier:DLINk:DLSCh:TBSalt3? |
|
Notes |
None and 37A are available when Modulation and TBS Index Table is Table 3. Otherwise, set to None and read-only. |
|
Preset |
NONe |
|
State Saved |
Yes |
|
Min |
N/A |
|
Max |
N/A |
|
Initial S/W Revision |
A.20.01 |
Sets the Virtual Resource Block Type for Resource Allocation Type 2.
|
SCPI Command |
[:SOURce]:RADio:LTETdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<N>:VRBType LOC|DIST [:SOURce]:RADio:LTETdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<N>:VRBType? |
|
SCPI Example |
:RADio:LTETdd:WAVeform:ARB:CCARrier:DLINk:DLSCh1:VRBType LOC :RADio:LTETdd:WAVeform:ARB:CCARrier:DLINk:DLSCh1:VRBType? |
|
Notes |
LOC = Localized VRBs DIST = Distributed VRBs In distributed allocation mode, the RB gap in the PDSCH is valid and the RB size is limited to the maximum number for the distributed type. See Resource Allocation in 3GPP TS 36.213. |
|
Dependencies |
Applies to Resource Allocation Type 2. |
|
Preset |
LOC |
|
State Saved |
Yes |
|
Min |
N/A |
|
Max |
N/A |
|
Initial S/W Revision |
A.20.01 |
Sets the Resource Allocation Type for the DL-SCH.
|
SCPI Command |
[:SOURce]:RADio:LTETdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<N>:RATYpe T0|T1|T2 [:SOURce]:RADio:LTETdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<N>:RATYpe? |
|
SCPI Example |
:RADio:LTETdd:WAVeform:ARB:CCARrier:DLINk:DLSCh1:RATYpe T2 :RADio:LTETdd:WAVeform:ARB:CCARrier:DLINk:DLSCh1:RATYpe? |
|
Notes |
Type 0: bitmap per RBG Type 1: bitmap per RB subset Type 2: contiguous VRB. Refer to 3GPP TS 36.213 |
|
Preset |
T2 |
|
State Saved |
Yes |
|
Min |
N/A |
|
Max |
N/A |
|
Initial S/W Revision |
A.20.01 |
Selects the PDSCH Transmission Setting Mode.
|
SCPI Command |
[:SOURce]:RADio:LTETdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<N>:TMODe:SETTing MCS|MAN [:SOURce]:RADio:LTETdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<N>:TMODe:SETTing? |
|
SCPI Example |
:RADio:LTETdd:WAVeform:ARB:CCARrier:DLINk:DLSCh1:TMODe:SETTing MCS :RADio:LTETdd:WAVeform:ARB:CCARrier:DLINk:DLSCh1:TMODe:SETTing? |
|
Notes |
MCS: TB size and modulation are set by the MCS index according to 3GPP TS 36.213 7.1.7. MAN: manual TB size and modulation entry. |
|
Preset |
MCS |
|
State Saved |
Yes |
|
Min |
N/A |
|
Max |
N/A |
|
Initial S/W Revision |
A.20.01 |
Selects the Modulation and TBS Index Table for PDSCH.
|
SCPI Command |
[:SOURce]:RADio:LTETdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<N>:MCSTable TAB1|TAB2 [:SOURce]:RADio:LTETdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<N>:MCSTable? |
|
SCPI Example |
:RADio:LTETdd:WAVeform:ARB:CCARrier:DLINk:DLSCh:MCSTable TAB1 :RADio:LTETdd:WAVeform:ARB:CCARrier:DLINk:DLSCh:MCSTable? |
|
Notes |
|
|
Preset |
TAB1 |
|
State Saved |
Yes |
|
Min |
N/A |
|
Max |
N/A |
|
Initial S/W Revision |
A.20.01 |
Sets the length of the DL-SCH PDSCH transmission configuration (Tx Config) sequence.
|
SCPI Command |
[:SOURce]:RADio:LTETdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<N>:TXPLen <integer> [:SOURce]:RADio:LTETdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<N>:TXPLen? |
|
SCPI Example |
:RADio:LTETdd:WAVeform:ARB:CCARrier:DLINk:DLSCh:TXPLen 10 :RADio:LTETdd:WAVeform:ARB:CCARrier:DLINk:DLSCh:TXPLen? |
|
Dependencies |
Length of the per-subframe PDSCH Tx parameter (Transmission Configuration) sequence. |
|
Preset |
10 |
|
State Saved |
Yes |
|
Min |
10 |
|
Max |
16 |
|
Initial S/W Revision |
A.20.01 |
Sets the number of spatial multiplexing layers for the DL-SCH.
|
SCPI Command |
[:SOURce]:RADio:LTETdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<N>:NLAYer 1|2|3|4 [:SOURce]:RADio:LTETdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<N>:NLAYer? |
|
SCPI Example |
:RADio:LTETdd:WAVeform:ARB:CCARrier:DLINk:DLSCh:NLAYer 1 :RADio:LTETdd:WAVeform:ARB:CCARrier:DLINk:DLSCh:NLAYer? |
|
Notes |
|
|
Couplings |
Coupled with Transmission Mode and Number of Codewords. |
|
Preset |
1 |
|
State Saved |
Yes |
|
Min |
N/A |
|
Max |
N/A |
|
Initial S/W Revision |
A.20.01 |
Sets the number of codewords (transport blocks) for the DL-SCH.
|
SCPI Command |
[:SOURce]:RADio:LTETdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<N>:NCWord 1|2 [:SOURce]:RADio:LTETdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<N>:NCWord? |
|
SCPI Example |
:RADio:LTETdd:WAVeform:ARB:CCARrier:DLINk:DLSCh:NCWord 1 :RADio:LTETdd:WAVeform:ARB:CCARrier:DLINk:DLSCh:NCWord? |
|
Notes |
|
|
Couplings |
Coupled with Transmission Mode. |
|
Preset |
1 |
|
State Saved |
Yes |
|
Min |
N/A |
|
Max |
N/A |
|
Initial S/W Revision |
A.20.01 |
Enter a value for the Codebook Index when Spatial Multiplexing is selected as the diversity method.
See 3GPP TS 36.211 for more information.
|
SCPI Command |
[:SOURce]:RADio:LTETdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<N>:CBINdex <integer> [:SOURce]:RADio:LTETdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<N>:CBINdex? |
|
SCPI Example |
:RADio:LTETdd:WAVeform:ARB:CCARrier:DLINk:DLSCh:CBINdex 0 :RADio:LTETdd:WAVeform:ARB:CCARrier:DLINk:DLSCh:CBINdex? |
|
Notes |
Range depends on antenna port count and Number of Layers:
|
|
Dependencies |
Applicable when Spatial Multiplexing is selected as the Diversity Method. |
|
Preset |
0 |
|
State Saved |
Yes |
|
Min |
0 |
|
Max |
15 |
|
Initial S/W Revision |
A.20.01 |
Selects a diversity method.
|
SCPI Command |
[:SOURce]:RADio:LTETdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<N>:DIVMethod OFF|TXDiv|SMUX [:SOURce]:RADio:LTETdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<N>:DIVMethod? |
|
SCPI Example |
:RADio:LTETdd:WAVeform:ARB:CCARrier:DLINk:DLSCh:DIVMethod OFF :RADio:LTETdd:WAVeform:ARB:CCARrier:DLINk:DLSCh:DIVMethod? |
|
Choices |
Off | Tx Diversity | Spatial Multiplexing. Tx Diversity and Spatial Multiplexing are available only for multiple-antenna configurations. |
|
Couplings |
Controls Number of Layers and Number of Codewords. |
|
Preset |
OFF |
|
State Saved |
Yes |
|
Min |
N/A |
|
Max |
N/A |
|
Initial S/W Revision |
A.20.01 |
Selects a cyclic delay diversity (CDD) precoding method.
See 3GPP TS 36.211 for detailed information about precoding.
|
SCPI Command |
[:SOURce]:RADio:LTETdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<N>:PRECoding WCDD|LCDD [:SOURce]:RADio:LTETdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<N>:PRECoding? |
|
SCPI Example |
:RADio:LTETdd:WAVeform:ARB:CCARrier:DLINk:DLSCh:PRECoding WCDD :RADio:LTETdd:WAVeform:ARB:CCARrier:DLINk:DLSCh:PRECoding? |
|
Choices |
Without CDD | Large-Delay CDD |
|
Dependencies |
Applicable when Spatial Multiplexing is selected as the Diversity Method. |
|
Preset |
WCDD |
|
State Saved |
Yes |
|
Min |
N/A |
|
Max |
N/A |
|
Initial S/W Revision |
A.20.01 |
Turns the UE Specific Reference Signal (DM-RS) state on or off.
|
SCPI Command |
[:SOURce]:RADio:LTETdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<N>:UERS[:STATe] ON|OFF|1|0 [:SOURce]:RADio:LTETdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<N>:UERS[:STATe]? |
|
SCPI Example |
:RADio:LTETdd:WAVeform:ARB:CCARrier:DLINk:DLSCh:UERS:STATe OFF :RADio:LTETdd:WAVeform:ARB:CCARrier:DLINk:DLSCh:UERS:STATe? |
|
Dependencies |
Only available when Transmission Mode is 7 or 8. |
|
Couplings |
When ON, UE-specific DM-RS are transmitted. |
|
Preset |
0 |
|
State Saved |
Yes |
|
Min |
N/A |
|
Max |
N/A |
|
Initial S/W Revision |
A.20.01 |
Enter a power level, in dB for the DM-RS.
|
SCPI Command |
[:SOURce]:RADio:LTETdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<N>:UERS:POWer <rel_ampl> [:SOURce]:RADio:LTETdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<N>:UERS:POWer? |
|
SCPI Example |
:RADio:LTETdd:WAVeform:ARB:CCARrier<:DLINk:DLSCh:UERS:POWer 0 :RADio:LTETdd:WAVeform:ARB:CCARrier:DLINk:DLSCh:UERS:POWer? |
|
Notes |
Relative power (dB). |
|
Dependencies |
Read-only when UE-Specific Ref Sig State is OFF. |
|
Preset |
0 |
|
State Saved |
Yes |
|
Min |
-60 |
|
Max |
20 |
|
Initial S/W Revision |
A.20.01 |
Selects the antenna port for the UE-Specific Reference Signal (DM-RS) transmission.
|
SCPI Command |
[:SOURce]:RADio:LTETdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<N>:UERS:PORT P5|P7|P8|P78|P79|P710|P711|P712|P713|P714|NA [:SOURce]:RADio:LTETdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<N>:UERS:PORT? |
|
SCPI Example |
:RADio:LTETdd:WAVeform:ARB:CCARrier:DLINk:DLSCh:UERS:PORT P5 :RADio:LTETdd:WAVeform:ARB:CCARrier:DLINk:DLSCh:UERS:PORT? |
|
Notes |
P5 = Port 5 P7 = Port 7 P8 = Port 8 P78 = Port 7&8 P79-P714 = Port 7-9 .. 7-14 NA = not applicable |
|
Dependencies |
Read-only when UE-Specific Ref Sig State is OFF. Available choices depend on Transmission Mode, Number of Layers and Number of Codewords. |
|
Preset |
P5 |
|
State Saved |
Yes |
|
Min |
N/A |
|
Max |
N/A |
|
Initial S/W Revision |
A.20.01 |
Sets the Antenna Beam Configuration Mode to degree or complex.
|
SCPI Command |
[:SOURce]:RADio:LTETdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<N>:UERS:ABCMode DEG|COMP [:SOURce]:RADio:LTETdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<N>:UERS:ABCMode? |
|
SCPI Example |
:RADio:LTETdd:WAVeform:ARB:CCARrier:DLINk:DLSCh:UERS:ABCMode DEG :RADio:LTETdd:WAVeform:ARB:CCARrier:DLINk:DLSCh:UERS:ABCMode? |
|
Notes |
|
|
Dependencies |
Applicable only when using a beam-forming transmission. |
|
Preset |
DEG |
|
State Saved |
Yes |
|
Min |
N/A |
|
Max |
N/A |
|
Initial S/W Revision |
A.20.01 |
Sets the antenna beam main lobe direction for DM-RS Port 5, in degrees.
|
SCPI Command |
[:SOURce]:RADio:LTETdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<N>:UERS:BEAMport5 <angle> [:SOURce]:RADio:LTETdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<N>:UERS:BEAMport5? |
|
SCPI Example |
:RADio:LTETdd:WAVeform:CCARrier:DLINk:DLSCh:UERS:BEAMport5 0 :RADio:LTETdd:WAVeform:CCARrier:DLINk:DLSCh:UERS:BEAMport5? |
|
Dependencies |
Visible when Antenna Beam Config Mode = Degree, UE-Specific Ref Sig State = On, and Transmission Mode includes Port 5. |
|
Preset |
0 |
|
State Saved |
Yes |
|
Min |
-90 |
|
Max |
90 |
|
Initial S/W Revision |
A.20.01 |
Sets the antenna beam main lobe direction for DM-RS Port 7, in degrees.
|
SCPI Command |
[:SOURce]:RADio:LTETdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<N>:UERS:BEAMport7 <angle> [:SOURce]:RADio:LTETdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<N>:UERS:BEAMport7? |
|
SCPI Example |
:RADio:LTETdd:WAVeform:CCARrier:DLINk:DLSCh:UERS:BEAMport7 0 :RADio:LTETdd:WAVeform:CCARrier:DLINk:DLSCh:UERS:BEAMport7? |
|
Dependencies |
Visible when Antenna Beam Config Mode = Degree, UE-Specific Ref Sig State = On, and Transmission Mode includes Port 7. When set, the Transmit Antenna Weight for Port 7 is auto-calculated. The reverse conversion (complex to degree) does not apply. See 3GPP TS 36.211. |
|
Preset |
0 |
|
State Saved |
Yes |
|
Min |
-90 |
|
Max |
90 |
|
Initial S/W Revision |
A.20.01 |
Sets the antenna beam main lobe direction for DM-RS Port 8 in degrees.
|
SCPI Command |
[:SOURce]:RADio:LTETdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<N>:UERS:BEAMport8 <angle> [:SOURce]:RADio:LTETdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<N>:UERS:BEAMport8? |
|
SCPI Example |
:RADio:LTETdd:WAVeform:CCARrier:DLINk:DLSCh:UERS:BEAMport8 0 :RADio:LTETdd:WAVeform:CCARrier:DLINk:DLSCh:UERS:BEAMport8? |
|
Dependencies |
Visible when Antenna Beam Config Mode = Degree, UE-Specific Ref Sig State = On, and Transmission Mode includes Port 8. When set, the Transmit Antenna Weight for Port 8 is auto-calculated. The reverse conversion (complex to degree) does not apply. See 3GPP TS 36.211. |
|
Preset |
0 |
|
State Saved |
Yes |
|
Min |
-90 |
|
Max |
90 |
|
Initial S/W Revision |
A.20.01 |
Sets the antenna beam main lobe direction for DM-RS Port 9 in degrees.
|
SCPI Command |
[:SOURce]:RADio:LTETdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<N>:UERS:BEAMport9 <angle> [:SOURce]:RADio:LTETdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<N>:UERS:BEAMport9? |
|
SCPI Example |
:RADio:LTETdd:WAVeform:CCARrier:DLINk:DLSCh:UERS:BEAMport9 0 :RADio:LTETdd:WAVeform:CCARrier:DLINk:DLSCh:UERS:BEAMport9? |
|
Dependencies |
Visible when Antenna Beam Config Mode = Degree, UE-Specific Ref Sig State = On, and Transmission Mode includes Port 9. When set, the Transmit Antenna Weight for Port 9 is auto-calculated. The reverse conversion (complex to degree) does not apply. See 3GPP TS 36.211. |
|
Preset |
0 |
|
State Saved |
Yes |
|
Min |
-90 |
|
Max |
90 |
|
Initial S/W Revision |
A.20.01 |
Sets the antenna beam main lobe direction for DM-RS Port 10 in degrees.
|
SCPI Command |
[:SOURce]:RADio:LTETdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<N>:UERS:BEAMport10 <angle> [:SOURce]:RADio:LTETdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<N>:UERS:BEAMport10? |
|
SCPI Example |
:RADio:LTETdd:WAVeform:CCARrier:DLINk:DLSCh:UERS:BEAMport10 0 :RADio:LTETdd:WAVeform:CCARrier:DLINk:DLSCh:UERS:BEAMport10? |
|
Dependencies |
Visible when Antenna Beam Config Mode = Degree, UE-Specific Ref Sig State = On, and Transmission Mode includes Port 10. When set, the Transmit Antenna Weight for Port 10 is auto-calculated. The reverse conversion (complex to degree) does not apply. See 3GPP TS 36.211. |
|
Preset |
0 |
|
State Saved |
Yes |
|
Min |
-90 |
|
Max |
90 |
|
Initial S/W Revision |
A.20.01 |
Sets the antenna beam main lobe direction for DM-RS Port 11 in degrees.
|
SCPI Command |
[:SOURce]:RADio:LTETdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<N>:UERS:BEAMport11 <angle> [:SOURce]:RADio:LTETdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<N>:UERS:BEAMport11? |
|
SCPI Example |
:RADio:LTETdd:WAVeform:CCARrier:DLINk:DLSCh:UERS:BEAMport11 0 :RADio:LTETdd:WAVeform:CCARrier:DLINk:DLSCh:UERS:BEAMport11? |
|
Dependencies |
Visible when Antenna Beam Config Mode = Degree, UE-Specific Ref Sig State = On, and Transmission Mode includes Port 11. When set, the Transmit Antenna Weight for Port 11 is auto-calculated. The reverse conversion (complex to degree) does not apply. See 3GPP TS 36.211. |
|
Preset |
0 |
|
State Saved |
Yes |
|
Min |
-90 |
|
Max |
90 |
|
Initial S/W Revision |
A.20.01 |
Sets the antenna beam main lobe direction for DM-RS Port 12, in degrees.
|
SCPI Command |
[:SOURce]:RADio:LTETdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<N>:UERS:BEAMport12 <angle> [:SOURce]:RADio:LTETdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<N>:UERS:BEAMport12? |
|
SCPI Example |
:RADio:LTETdd:WAVeform:CCARrier:DLINk:DLSCh:UERS:BEAMport12 0 :RADio:LTETdd:WAVeform:CCARrier:DLINk:DLSCh:UERS:BEAMport12? |
|
Dependencies |
Visible when Antenna Beam Config Mode = Degree, UE-Specific Ref Sig State = On, and Transmission Mode includes Port 12. When set, the Transmit Antenna Weight for Port 12 is auto-calculated. The reverse conversion (complex to degree) does not apply. See 3GPP TS 36.211. |
|
Preset |
0 |
|
State Saved |
Yes |
|
Min |
-90 |
|
Max |
90 |
|
Initial S/W Revision |
A.20.01 |
Sets the antenna beam main lobe direction for DM-RS Port 13, in degrees.
|
SCPI Command |
[:SOURce]:RADio:LTETdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<N>:UERS:BEAMport13 <angle> [:SOURce]:RADio:LTETdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<N>:UERS:BEAMport13? |
|
SCPI Example |
:RADio:LTETdd:WAVeform:CCARrier:DLINk:DLSCh:UERS:BEAMport13 0 :RADio:LTETdd:WAVeform:CCARrier:DLINk:DLSCh:UERS:BEAMport13? |
|
Dependencies |
Visible when Antenna Beam Config Mode = Degree, UE-Specific Ref Sig State = On, and Transmission Mode includes Port 13. When set, the Transmit Antenna Weight for Port 13 is auto-calculated. The reverse conversion (complex to degree) does not apply. See 3GPP TS 36.211. |
|
Preset |
0 |
|
State Saved |
Yes |
|
Min |
-90 |
|
Max |
90 |
|
Initial S/W Revision |
A.20.01 |
Sets the antenna beam main lobe direction for DM-RS Port 14, in degrees.
|
SCPI Command |
[:SOURce]:RADio:LTETdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<N>:UERS:BEAMport14 <angle> [:SOURce]:RADio:LTETdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<N>:UERS:BEAMport14? |
|
SCPI Example |
:RADio:LTETdd:WAVeform:CCARrier:DLINk:DLSCh:UERS:BEAMport14 0 :RADio:LTETdd:WAVeform:CCARrier:DLINk:DLSCh:UERS:BEAMport14? |
|
Dependencies |
Visible when Antenna Beam Config Mode = Degree, UE-Specific Ref Sig State = On, and Transmission Mode includes Port 14. When set, the Transmit Antenna Weight for Port 14 is auto-calculated. The reverse conversion (complex to degree) does not apply. See 3GPP TS 36.211. |
|
Preset |
0 |
|
State Saved |
Yes |
|
Min |
-90 |
|
Max |
90 |
|
Initial S/W Revision |
A.20.01 |
Sets the transmit antenna weight for DM-RS Port 5 as a complex string (e.g. "1.0+0.0j").
For multi-antenna configurations, provide one complex value per antenna separated by commas (e.g. "1.0+0.0j,0.5+0.5j").
|
SCPI Command |
[:SOURce]:RADio:LTETdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<N>:UERS:WEIGhtport5 <string> [:SOURce]:RADio:LTETdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<N>:UERS:WEIGhtport5? |
|
SCPI Example |
:RADio:LTETdd:WAVeform:CCARrier:DLINk:DLSCh:UERS:WEIGhtport5 "1" :RADio:LTETdd:WAVeform:CCARrier:DLINk:DLSCh:UERS:WEIGhtport5? |
|
Notes |
The count must be equal to the Total Number of Antennas. When Antenna Beam degree is changed, this weight is auto-calculated; the reverse does not apply. See 3GPP TS 36.211. |
|
Couplings |
|
|
Preset |
"1" when total number of antennas is 1. "1,1" when total number of antennas is 2. "1,1,1,1" when total number of antennas is 4. "1,1,1,1,1,1,1,1" when total number of antennas is 8. |
|
State Saved |
Yes |
|
Initial S/W Revision |
A.20.01 |
Sets the transmit antenna weight for DM-RS Port 7 as a complex string (e.g. "1.0+0.0j").
For multi-antenna configurations, provide one complex value per antenna
separated by commas (e.g. "1.0+0.0j,0.5+0.5j").
|
SCPI Command |
[:SOURce]:RADio:LTETdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<N>:UERS:WEIGhtport7 <string> [:SOURce]:RADio:LTETdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<N>:UERS:WEIGhtport7? |
|
SCPI Example |
:RADio:LTETdd:WAVeform:CCARrier:DLINk:DLSCh:UERS:WEIGhtport7 "1,1" :RADio:LTETdd:WAVeform:CCARrier:DLINk:DLSCh:UERS:WEIGhtport7? |
|
Dependencies |
The count must be equal to Total Number of Antennas. Visible when Antenna Beam Configuration Mode = Complex, DM-RS State = When Antenna Beam degree is changed, this weight is auto-calculated; the See 3GPP TS 36.211. |
|
Preset |
"1,1" when total number of antennas is 2. |
|
State Saved |
Yes |
|
Initial S/W Revision |
A.20.01 |
Sets the transmit antenna weight for DM-RS Port 8 as a complex string (e.g. "1.0+0.0j").
For multi-antenna configurations, provide one complex value per antenna separated by commas (e.g. "1.0+0.0j,0.5+0.5j").
|
SCPI Command |
[:SOURce]:RADio:LTETdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<N>:UERS:WEIGhtport8 <string> [:SOURce]:RADio:LTETdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<N>:UERS:WEIGhtport8? |
|
SCPI Example |
:RADio:LTETdd:WAVeform:CCARrier:DLINk:DLSCh:UERS:WEIGhtport8 "1,1,1,1" :RADio:LTETdd:WAVeform:CCARrier:DLINk:DLSCh:UERS:WEIGhtport8? |
|
Dependencies |
The count must be equal to Total Number of Antennas. Visible when Antenna Beam Configuration Mode = Complex, DM-RS State = On, TM is 8, Transmit Antenna Port is Port 8, Total number of antennas is 4 Antennas. When Antenna Beam degree is changed, this weight is auto-calculated; the reverse does not apply. |
|
Couplings |
|
|
Preset |
"1,1,1,1" when total number of antennas is 4. "1,1,1,1,1,1,1,1" when total number of antennas is 8. |
|
State Saved |
Yes |
|
Initial S/W Revision |
A.20.01 |
Sets the transmit antenna weight for DM-RS Port 9 as a complex complex string (e.g. "1.0+0.0j").
For multi-antenna configurations, provide one complex value per antenna separated by commas (e.g. "1.0+0.0j,0.5+0.5j").
|
SCPI Command |
[:SOURce]:RADio:LTETdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<N>:UERS:WEIGhtport9 <string> [:SOURce]:RADio:LTETdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<N>:UERS:WEIGhtport9? |
|
SCPI Example |
:RADio:LTETdd:WAVeform:CCARrier:DLINk:DLSCh:UERS:WEIGhtport9 "1,1,1,1" :RADio:LTETdd:WAVeform:CCARrier:DLINk:DLSCh:UERS:WEIGhtport9? |
|
Dependencies |
The count must be equal to Total Number of Antennas. When Antenna Beam degree is changed, this weight is auto-calculated; the reverse does not apply. See 3GPP TS 36.211. |
|
Couplings |
|
|
Preset |
"1" when total number of antennas is 1. "1,1" when total number of antennas is 2. "1,1,1,1" when total number of antennas is 4. "1,1,1,1,1,1,1,1" when total number of antennas is 8. |
|
State Saved |
Yes |
|
Initial S/W Revision |
A.20.01 |
Sets the transmit antenna weight for DM-RS Port 10 as a complex string (e.g. "1.0+0.0j").
For multi-antenna configurations, provide one complex value per antenna separated by commas (e.g. "1.0+0.0j,0.5+0.5j").
|
SCPI Command |
[:SOURce]:RADio:LTETdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<N>:UERS:WEIGhtport10 <string> [:SOURce]:RADio:LTETdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<N>:UERS:WEIGhtport10? |
|
SCPI Example |
:RADio:LTETdd:WAVeform:CCARrier:DLINk:DLSCh:UERS:WEIGhtport10 "1,1,1,1" :RADio:LTETdd:WAVeform:CCARrier:DLINk:DLSCh:UERS:WEIGhtport10? |
|
Dependencies |
The count must be equal to Total Number of Antennas. Visible when Antenna Beam Configuration Mode = Complex, DM-RS State = On, TM is 9, Transmit Antenna Port is Port 7-10, Total number of antennas is 4 Antennas. When Antenna Beam degree is changed, this weight is auto-calculated; the reverse does not apply. See 3GPP TS 36.211. |
|
Couplings |
|
|
Preset |
"1,1,1,1" when total number of antennas is 4. "1,1,1,1,1,1,1,1" when total number of antennas is 8. |
|
State Saved |
Yes |
|
Initial S/W Revision |
A.20.01 |
Sets the transmit antenna weight for DM-RS Port 11 as a complex string (e.g. "1.0+0.0j").
For multi-antenna configurations, provide one complex value per antenna separated by commas (e.g. "1.0+0.0j,0.5+0.5j").
|
SCPI Command |
[:SOURce]:RADio:LTETdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<N>:UERS:WEIGhtport11 <string> [:SOURce]:RADio:LTETdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<N>:UERS:WEIGhtport11? |
|
SCPI Example |
:RADio:LTETdd:WAVeform:CCARrier:DLINk:DLSCh:UERS:WEIGhtport11 "1,1,1,1,1,1,1,1" :RADio:LTETdd:WAVeform:CCARrier:DLINk:DLSCh:UERS:WEIGhtport11? |
|
Dependencies |
The count must be equal to Total Number of Antennas. Visible when Antenna Beam Configuration Mode = Complex, DM-RS State = On, TM is 9, Transmit Antenna Port is Port 7-11, Total number of antennas is 8 Antennas. When Antenna Beam degree is changed, this weight is auto-calculated; the reverse does not apply. See 3GPP TS 36.211. |
|
Couplings |
|
|
Preset |
"1,1,1,1,1,1,1,1" |
|
State Saved |
Yes |
|
Initial S/W Revision |
A.20.01 |
Sets the transmit antenna weight for DM-RS Port 12 as a complex string (e.g. "1.0+0.0j").
For multi-antenna configurations, provide one complex value per antenna separated by commas (e.g. "1.0+0.0j,0.5+0.5j").
|
SCPI Command |
[:SOURce]:RADio:LTETdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<N>:UERS:WEIGhtport12 <string> [:SOURce]:RADio:LTETdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<N>:UERS:WEIGhtport12? |
|
SCPI Example |
:RADio:LTETdd:WAVeform:CCARrier:DLINk:DLSCh:UERS:WEIGhtport12 "1,1,1,1,1,1,1,1" :RADio:LTETdd:WAVeform:CCARrier:DLINk:DLSCh:UERS:WEIGhtport12? |
|
Dependencies |
The count must be equal to Total Number of Antennas. Visible when Antenna Beam Configuration Mode = Complex, DM-RS State = On, TM is 9, Transmit Antenna Port is Port 7-12, Total number of antennas is 8 Antennas. When Antenna Beam degree is changed, this weight is auto-calculated; the reverse does not apply. See 3GPP TS 36.211. |
|
Couplings |
|
|
Preset |
"1,1,1,1,1,1,1,1" |
|
State Saved |
Yes |
|
Initial S/W Revision |
A.20.01 |
Sets the transmit antenna weight for DM-RS Port 13 as a complex string (e.g. "1.0+0.0j").
For multi-antenna configurations, provide one complex value per antenna separated by commas (e.g. "1.0+0.0j,0.5+0.5j").
|
SCPI Command |
[:SOURce]:RADio:LTETdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<N>:UERS:WEIGhtport13 <string> [:SOURce]:RADio:LTETdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<N>:UERS:WEIGhtport13? |
|
SCPI Example |
:RADio:LTETdd:WAVeform:CCARrier:DLINk:DLSCh:UERS:WEIGhtport13 "1,1,1,1,1,1,1,1" :RADio:LTETdd:WAVeform:CCARrier:DLINk:DLSCh:UERS:WEIGhtport13? |
|
Dependencies |
The count must be equal to Total Number of Antennas. Visible when Antenna Beam Configuration Mode = Complex, DM-RS State = On, TM is 9, Transmit Antenna Port is Port 7-13, Total number of antennas is 8 Antennas. When Antenna Beam degree is changed, this weight is auto-calculated; the reverse does not apply. See 3GPP TS 36.211. |
|
Couplings |
|
|
Preset |
"1,1,1,1,1,1,1,1" |
|
State Saved |
Yes |
|
Initial S/W Revision |
A.20.01 |
Sets the transmit antenna weight for DM-RS Port 14 as a complex string (e.g. "1.0+0.0j").
For multi-antenna configurations, provide one complex value per antenna separated by commas (e.g. "1.0+0.0j,0.5+0.5j").
|
SCPI Command |
[:SOURce]:RADio:LTETdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<N>:UERS:WEIGhtport14 <string> [:SOURce]:RADio:LTETdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<N>:UERS:WEIGhtport14? |
|
SCPI Example |
:RADio:LTETdd:WAVeform:CCARrier:DLINk:DLSCh:UERS:WEIGhtport14 "1,1,1,1,1,1,1,1" :RADio:LTETdd:WAVeform:CCARrier:DLINk:DLSCh:UERS:WEIGhtport14? |
|
Dependencies |
The count must be equal to Total Number of Antennas. Visible when Antenna Beam Configuration Mode = Complex, DM-RS State = On, TM is 9, Transmit Antenna Port is Port 7-14, Total number of antennas is 8 Antennas. When Antenna Beam degree is changed, this weight is auto-calculated; the reverse does not apply. See 3GPP TS 36.211. |
|
Preset |
"1,1,1,1,1,1,1,1" |
|
State Saved |
Yes |
|
Initial S/W Revision |
A.20.01 |
Sets the number of available HARQ processes for the DL-SCH.
|
SCPI Command |
[:SOURce]:RADio:LTETdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<N>:HARQ:NPRoc <integer> [:SOURce]:RADio:LTETdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<N>:HARQ:NPRoc? |
|
SCPI Example |
:RADio:LTETdd:WAVeform:ARB:CCARrier:DLINk:DLSCh:HARQ:NPRoc 4 :RADio:LTETdd:WAVeform:ARB:CCARrier:DLINk:DLSCh:HARQ:NPRoc? |
|
Notes |
Defines the interval (number of subframes) between retransmissions. |
|
State Saved |
Yes |
|
Min |
1 |
|
Max |
4 (UL/DL Configuration 0) 7 (UL/DL Configuration 1) 10 (UL/DL Configuration 2) 9 (UL/DL Configuration 3) 12 (UL/DL Configuration 4) 15 (UL/DL Configuration 5) 6 (UL/DL Configuration 6) |
|
Initial S/W Revision |
A.20.01 |
Enter the numbers of individual HARQ processes, separated by commas or a range, to enable specific HARQ processes.
|
SCPI Command |
[:SOURce]:RADio:LTETdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<N>:HARQ:APRoc <string> [:SOURce]:RADio:LTETdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<N>:HARQ:APRoc? |
|
SCPI Example |
:RADio:LTETdd:WAVeform:ARB:CCARrier:DLINk:DLSCh:HARQ:APRoc "0" :RADio:LTETdd:WAVeform:ARB:CCARrier:DLINk:DLSCh:HARQ:APRoc? |
|
Notes |
Comma-separated HARQ process index sequence, or a range (for example 0-3). |
|
Range |
0 to (Number of HARQ Processes - 1) |
|
Preset |
0-3 |
|
State Saved |
Yes |
|
Min |
N/A |
|
Max |
N/A |
|
Initial S/W Revision |
A.20.01 |
Sets the RV Index Configuration for the DL-SCH.
|
SCPI Command |
[:SOURce]:RADio:LTETdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<N>:HARQ:RVConf AUTo|MANual [:SOURce]:RADio:LTETdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<N>:HARQ:RVConf? |
|
SCPI Example |
:RADio:LTETdd:WAVeform:ARB:CCARrier:DLINk:DLSCh:HARQ:RVConf AUTo :RADio:LTETdd:WAVeform:ARB:CCARrier:DLINk:DLSCh:HARQ:RVConf? |
|
Notes |
|
|
Couplings |
When Auto, RV Index Sequence is set by software. |
|
Preset |
AUTo |
|
State Saved |
Yes |
|
Min |
N/A |
|
Max |
N/A |
|
Initial S/W Revision |
A.20.01 |
Enter the numbers of individual RV Index Sequence values, separated by commas.
|
SCPI Command |
[:SOURce]:RADio:LTETdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<N>:HARQ:RVSeq <string> [:SOURce]:RADio:LTETdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<N>:HARQ:RVSeq? |
|
SCPI Example |
:RADio:LTETdd:WAVeform:ARB:CCARrier:DLINk:DLSCh:HARQ:RVSeq "0,2,3,1" :RADio:LTETdd:WAVeform:ARB:CCARrier:DLINk:DLSCh:HARQ:RVSeq? |
|
Notes |
Comma-separated RV index sequence, e.g. "0,2,3,1". Range of sequence length: 1-16; range of each value: 0-3. |
|
Dependencies |
Read-only when RV Index Configuration is AUTo. |
|
Preset |
0,2,3,1 |
|
State Saved |
Yes |
|
Min |
N/A |
|
Max |
N/A |
|
Initial S/W Revision |
A.20.01 |
Configures the dedicated Downlink Control Information (DCI/PDCCH) channel linked to this DL-SCH channel.
Turns the dedicated DCI channel for this DL-SCH on or off.
|
SCPI Command |
[:SOURce]:RADio:LTETdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<N>:DCI:[:STATe] ON|OFF|1|0 [:SOURce]:RADio:LTETdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<N>:DCI:[:STATe]? |
|
SCPI Example |
:RADio:LTETdd:WAVeform:ARB:CCARrier:DLINk:DLSCh:DCI:STATe OFF :RADio:LTETdd:WAVeform:ARB:CCARrier:DLINk:DLSCh:DCI:STATe? |
|
Preset |
0 |
|
State Saved |
Yes |
|
Min |
N/A |
|
Max |
N/A |
|
Initial S/W Revision |
A.20.01 |
Sets the Format of the dedicated DCI for this DL-SCH.
|
SCPI Command |
[:SOURce]:RADio:LTETdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<N>:DCI:FORMat F1|F1A|F1B|F1C|F1D|F2|F2A|F2B|F2C|F2D [:SOURce]:RADio:LTETdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<N>:DCI:FORMat? |
|
SCPI Example |
:RADio:LTETdd:WAVeform:ARB:CCARrier:DLINk:DLSCh:DCI:FORMat F1A :RADio:LTETdd:WAVeform:ARB:CCARrier:DLINk:DLSCh:DCI:FORMat? |
|
Notes |
The available DCI formats differ with different resource allocation types and MIMO settings. Refer to 3GPP TS 36.213 7.1 for the DCI format selection under different transmission modes. |
|
Preset |
F1A |
|
State Saved |
Yes |
|
Min |
N/A |
|
Max |
N/A |
|
Initial S/W Revision |
A.20.01 |
Enter a value for the Radio Network Temporary Identifier (RNTI) of the dedicated DCI.
|
SCPI Command |
[:SOURce]:RADio:LTETdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<N>:DCI:RNTi <integer> [:SOURce]:RADio:LTETdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<N>:DCI:RNTi? |
|
SCPI Example |
:RADio:LTETdd:WAVeform:ARB:CCARrier:DLINk:DLSCh:DCI:RNTi 0 :RADio:LTETdd:WAVeform:ARB:CCARrier:DLINk:DLSCh:DCI:RNTi? |
|
Couplings |
Coupled with the RNTI parameter in the DL-SCH General settings. |
|
Preset |
0 |
|
State Saved |
Yes |
|
Min |
0 |
|
Max |
65535 |
|
Initial S/W Revision |
A.20.01 |
Sets the transmission couple state between the dedicated DCI and DL-SCH.
|
SCPI Command |
[:SOURce]:RADio:LTETdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<N>:DCI:TXCouple DLSCh|MANual [:SOURce]:RADio:LTETdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<N>:DCI:TXCouple? |
|
SCPI Example |
:RADio:LTETdd:WAVeform:ARB:CCARrier:DLINk:DLSCh:DCI:TXCouple DLSCh :RADio:LTETdd:WAVeform:ARB:CCARrier:DLINk:DLSCh:DCI:TXCouple? |
|
Notes |
If DLSCH, the transmission state of DCI and DL-SCH are coupled when you set the transmission state of PDCCH or PDSCH in each subframe. |
|
Preset |
DLSCh |
|
State Saved |
Yes |
|
Min |
N/A |
|
Max |
N/A |
|
Initial S/W Revision |
A.20.01 |
Sets the UE Tx Antenna for the dedicated DCI channel.
|
SCPI Command |
[:SOURce]:RADio:LTETdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<N>:DCI:UTXantenna PORT0|PORT1 [:SOURce]:RADio:LTETdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<N>:DCI:UTXantenna? |
|
SCPI Example |
:RADio:LTETdd:WAVeform:ARB:CCARrier:DLINk:DLSCh:DCI:UTXantenna PORT0 :RADio:LTETdd:WAVeform:ARB:CCARrier:DLINk:DLSCh:DCI:UTXantenna? |
|
Preset |
PORT0 |
|
State Saved |
Yes |
|
Min |
N/A |
|
Max |
N/A |
|
Initial S/W Revision |
A.20.01 |
Sets the search space of the dedicated DCI (PDCCH) channel.
|
SCPI Command |
[:SOURce]:RADio:LTETdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<N>:DCI:SSPace COMMon|UESPecific [:SOURce]:RADio:LTETdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<N>:DCI:SSPace? |
|
SCPI Example |
:RADio:LTETdd:WAVeform:ARB:CCARrier:DLINk:DLSCh:DCI:SSPace COMMon :RADio:LTETdd:WAVeform:ARB:CCARrier:DLINk:DLSCh:DCI:SSPace? |
|
Notes |
See the PDCCH Assignment Procedure in 3GPP TS 36.213 9.1.1. |
|
Preset |
COMMon |
|
State Saved |
Yes |
|
Min |
N/A |
|
Max |
N/A |
|
Initial S/W Revision |
A.20.01 |
Configures the per-subframe PDCCH transmission (Tx Config) sequence for the dedicated DCI channel of this DL-SCH. Up to 160 sequences. Click the button in this cell to open the DL-SCH PDCCH Tx Setting window.
Enables or disables this dedicated DCI Tx sequence.
|
SCPI Command |
[:SOURce]:RADio:LTETdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<N>:DCI:TX<seq>:[:STATe] ON|OFF|1|0 [:SOURce]:RADio:LTETdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<N>:DCI:TX<seq>:[:STATe]? |
|
SCPI Example |
:RADio:LTETdd:WAVeform:ARB:CCARrier:DLINk:DLSCh:DCI:TX1:STATe OFF :RADio:LTETdd:WAVeform:ARB:CCARrier:DLINk:DLSCh:DCI:TX1:STATe? |
|
Notes |
Click to turn the DCI state on or off in the selected subframe. |
|
Preset |
0 |
|
State Saved |
Yes |
|
Min |
N/A |
|
Max |
N/A |
|
Initial S/W Revision |
A.20.01 |
Selects the TPC command for PUCCH in the selected subframe.
|
SCPI Command |
[:SOURce]:RADio:LTETdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<N>:DCI:TX<seq>:PUCCh:TPC TPC0|TPC1|TPC2|TPC3 [:SOURce]:RADio:LTETdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<N>:DCI:TX<seq>:PUCCh:TPC? |
|
SCPI Example |
:RADio:LTETdd:WAVeform:ARB:CCARrier:DLINk:DLSCh:DCI:TX1:PUCCh:TPC TPC0 :RADio:LTETdd:WAVeform:ARB:CCARrier:DLINk:DLSCh:DCI:TX1:PUCCh:TPC? |
|
Notes |
TPC #0 (-1 dB) | TPC #1 (0 dB) | TPC #2 (1 dB) | TPC #3 (3 dB). |
|
Preset |
TPC0 |
|
State Saved |
Yes |
|
Min |
N/A |
|
Max |
N/A |
|
Initial S/W Revision |
A.20.01 |
Sets the Downlink Assignment Index (DAI) field of the DCI information in the selected subframe.
|
SCPI Command |
[:SOURce]:RADio:LTETdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<N>:DCI:TX<seq>:DAI <integer> [:SOURce]:RADio:LTETdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<N>:DCI:TX<seq>:DAI? |
|
SCPI Example |
:RADio:LTETdd:WAVeform:ARB:CCARrier:DLINk:DLSCh:DCI:TX1:DAI 0 :RADio:LTETdd:WAVeform:ARB:CCARrier:DLINk:DLSCh:DCI:TX1:DAI? |
|
Preset |
0 |
|
State Saved |
Yes |
|
Min |
0 |
|
Max |
3 |
|
Initial S/W Revision |
A.20.01 |
Sets the SRS Request field of the DCI information in the selected subframe.
|
SCPI Command |
[:SOURce]:RADio:LTETdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<N>:DCI:TX<seq>:SRSReq <integer> [:SOURce]:RADio:LTETdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<N>:DCI:TX<seq>:SRSReq? |
|
SCPI Example |
:RADio:LTETdd:WAVeform:ARB:CCARrier:DLINk:DLSCh:DCI:TX1:SRSReq 0 :RADio:LTETdd:WAVeform:ARB:CCARrier:DLINk:DLSCh:DCI:TX1:SRSReq? |
|
Notes |
Triggers an aperiodic Sounding Reference Signal (SRS) transmission from the UE. See 3GPP TS 36.213 8.2 for details. |
|
Preset |
0 |
|
State Saved |
Yes |
|
Min |
0 |
|
Max |
3 |
|
Initial S/W Revision |
A.20.01 |
Selects the aggregation level for the DCI search space in the selected subframe.
|
SCPI Command |
[:SOURce]:RADio:LTETdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<N>:DCI:TX<seq>:AGGLevel L1|L2|L4|L8 [:SOURce]:RADio:LTETdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<N>:DCI:TX<seq>:AGGLevel? |
|
SCPI Example |
:RADio:LTETdd:WAVeform:ARB:CCARrier:DLINk:DLSCh:DCI:TX1:AGGLevel L1 :RADio:LTETdd:WAVeform:ARB:CCARrier:DLINk:DLSCh:DCI:TX1:AGGLevel? |
|
Notes |
See the PDCCH Assignment Procedure in 3GPP TS 36.213 9.1.1. |
|
Preset |
L1 |
|
State Saved |
Yes |
|
Min |
N/A |
|
Max |
N/A |
|
Initial S/W Revision |
A.20.01 |
Sets the PDCCH candidate index within the search space in the selected subframe.
|
SCPI Command |
[:SOURce]:RADio:LTETdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<N>:DCI:TX<seq>:CANDidate <integer> [:SOURce]:RADio:LTETdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<N>:DCI:TX<seq>:CANDidate? |
|
SCPI Example |
:RADio:LTETdd:WAVeform:ARB:CCARrier:DLINk:DLSCh:DCI:TX1:CANDidate 0 :RADio:LTETdd:WAVeform:ARB:CCARrier:DLINk:DLSCh:DCI:TX1:CANDidate? |
|
Notes |
See the PDCCH Assignment Procedure in 3GPP TS 36.213 9.1.1. |
|
Preset |
0 |
|
State Saved |
Yes |
|
Min |
0 |
|
Max |
5 |
|
Initial S/W Revision |
A.20.01 |
Query only
Displays the CCE (Control Channel Element) offset.
|
SCPI Command |
[:SOURce]:RADio:LTETdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<N>:DCI:TX<seq>:CCE:OFFSet? |
|
SCPI Example |
:RADio:LTETdd:WAVeform:ARB:CCARrier:DLINk:DLSCh:DCI:TX1:CCE:OFFSet? |
|
Notes |
See the PDCCH Assignment Procedure in 3GPP TS 36.213 9.1.1. |
|
Dependencies |
|
|
Couplings |
|
|
Preset |
11 |
|
State Saved |
Yes |
|
Min |
0 |
|
Max |
1023 |
|
Initial S/W Revision |
A.20.01 |
Sets the Scrambling Identity (SCID) field of the DCI information in the selected subframe.
|
SCPI Command |
[:SOURce]:RADio:LTETdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<N>:DCI:TX<seq>:SCID <integer> [:SOURce]:RADio:LTETdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<N>:DCI:TX<seq>:SCID? |
|
SCPI Example |
:RADio:LTETdd:WAVeform:ARB:CCARrier:DLINk:DLSCh:DCI:TX1:SCID 0 :RADio:LTETdd:WAVeform:ARB:CCARrier:DLINk:DLSCh:DCI:TX1:SCID? |
|
Notes |
Scrambling identity used to derive the DM-RS/PDSCH scrambling sequence for MU-MIMO operation (DCI format 2B/2C). |
|
Preset |
0 |
|
State Saved |
Yes |
|
Min |
0 |
|
Max |
1 |
|
Initial S/W Revision |
A.20.01 |
Sets the PMI Confirmation type of PDSCH in the selected subframe.
|
SCPI Command |
[:SOURce]:RADio:LTETdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<N>:DCI:TX<seq>:PMIConf INDicated|LATest [:SOURce]:RADio:LTETdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<N>:DCI:TX<seq>:PMIConf? |
|
SCPI Example |
:RADio:LTETdd:WAVeform:ARB:CCARrier:DLINk:DLSCh:DCI:TX1:PMIConf INDicated :RADio:LTETdd:WAVeform:ARB:CCARrier:DLINk:DLSCh:DCI:TX1:PMIConf? |
|
Notes |
Indicate in TPMI | Indicate in latest PMI on PUSCH. |
|
Dependencies |
Only available when the DCI format is 1B. |
|
Preset |
INDicated |
|
State Saved |
Yes |
|
Min |
N/A |
|
Max |
N/A |
|
Initial S/W Revision |
A.20.01 |
Sets the DL power offset of PDSCH in the selected subframe.
|
SCPI Command |
[:SOURce]:RADio:LTETdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<N>:DCI:TX<seq>:DLPoffset M10Log10_2db|ZERodb [:SOURce]:RADio:LTETdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<N>:DCI:TX<seq>:DLPoffset? |
|
SCPI Example |
:RADio:LTETdd:WAVeform:ARB:CCARrier:DLINk:DLSCh:DCI:TX1:DLPoffset ZERodb :RADio:LTETdd:WAVeform:ARB:CCARrier:DLINk:DLSCh:DCI:TX1:DLPoffset? |
|
Notes |
-10*log10(2) dB | 0 dB |
|
Dependencies |
Only available when the DCI format is 1D. |
|
Preset |
ZERodb |
|
State Saved |
Yes |
|
Min |
N/A |
|
Max |
N/A |
|
Initial S/W Revision |
A.20.01 |
Sets the codeword swap state of PDSCH in the selected subframe.
|
SCPI Command |
[:SOURce]:RADio:LTETdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<N>:DCI:TX<seq>:CWSWap ON|OFF|1|0 [:SOURce]:RADio:LTETdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DLSCh<N>:DCI:TX<seq>:CWSWap? |
|
SCPI Example |
:RADio:LTETdd:WAVeform:ARB:CCARrier:DLINk:DLSCh:DCI:TX1:CWSWap OFF :RADio:LTETdd:WAVeform:ARB:CCARrier:DLINk:DLSCh:DCI:TX1:CWSWap? |
|
Notes |
If the codeword swap state is true, the transport block information is swapped in the DCI content. |
|
Dependencies |
Only available when the DCI format is 2 or 2A. |
|
Preset |
0 |
|
State Saved |
Yes |
|
Min |
N/A |
|
Max |
N/A |
|
Initial S/W Revision |
A.20.01 |